Specification
Photo # | 1004 |
---|
Landrum Performance Front Drag Racing Coil Springs are designed to deliver the performance, reliability, and consistency you need to win. Landrum front drag race springs are taller than OEM springs and use softer rates to give your car the correct ride height while providing more stored energy for instant weight transfer during launch. This helps to give you increased torque control, reduced wheel hop, and faster 60ft and 1/4-mile ET’s.
Landrum drag race springs are available for the front suspension of GM vehicles and are offered in configurations to fit OEM A-Arms and Aftermarket A-Arms with no modifications required. Springs with a 5” outer diameter and 18” length are available for 1964-1972 GM vehicles, and springs with a 5.5” outer diameter and 18” length are offered for 1973 and newer models.
Our Front Drag Racing Coil Springs are available in a range of rates including:
All front springs are closed and ground on one end to provide proper contact with the frame. The opposite end is either open to properly fit into the lower control arm of OEM A-Arms or closed for Aftermarket A-Arms.
Landrum Performance Front Drag Racing Coil Springs are light weight, high travel and made with the highest-grade High Tinsel Chrome Silicon Steel wire.
The drag race springs are cold wound, not hot wound. Each is properly heat treated and stress relieved to ensure the sides of the spring remain parallel during installation.
All Landrum Front Drag Racing Coil Springs use standardized testing procedures to ensure the best quality and performance.
Our springs are powder coated and not plated which avoids hydrogen embrittlement, a condition that can be caused by electroplating and can weaken metal.
Each spring is manufactured with the highest tolerance in mind and is designed with the correct pitch and height ratio to insure a consistent rate throughout the entire cycle.
This Spring Compressor makes it easy to install our 18” Front Drag Racing Coil Springs. Standard spring compressors just aren’t long enough to properly compress 18” springs, but our spring compressor is. The spring compressor is inserted through the top shock absorber opening and a long length threaded rod allows the compressor fingers to reach down to the bottom of the spring. A position adjustable bearing located toward the top of the rod seats on the top of the shock opening so the threaded rod turns freely when the spring compressor is tensioned or loosened.
Retail Price: $169.00
To purchase a spring compressor:
Download “Spring-Compressor-Instructions-2.0.pdf”
Spring-Compressor-Instructions-2.0.pdf – Downloaded 4016 times – 199.22 KB
Photo # | 1004 |
---|
Landrum Street Stock/Stock Appearing Front Coil Springs are engineered for racing classes that require stock appearing front springs and don’t require use of spacers or weight jacks.
Street Stock and Stock Appearing Front Coil Springs are available in a choice of diameters, free lengths, and spring rates to fit your application.
Additional Landrum Performance Springs technical information can be found here.
Elite Series Dirt Modified springs and Stock Car springs give you the winning edge. Elite Series Coil Springs are designed to be the best of the best and are Landrum’s highest performance springs. Whether used on oval dirt cars or oval pavement cars, superior Landrum engineering and performance leads the way.
Landrum Performance has created the Elite Series line of racing coil springs specifically for IMCA and UMP series cars.
More information about the manufacturing of Landrum Dirt Modified Springs as well as our other coil springs can be found here.
Landrum Performance Stock Appearing Pig Tail Rear Springs are for circle track and drag racing classes that require stock appearing springs which use only one pig tail hookup and don’t require use of spacers or weight jacks.
The 5.5” OD Stock Appearing Springs are available in 9” and 11” lengths and are painted black for a stock appearance. A wide range of spring rates makes it easy to find the rate you need. Springs are closed and ground on both ends to fit stock mounting points.
Landrum Stock Appearing Pig Tail Rear Springs are built for those who demand the best spring performance and provide the reliability and durability you need to win.
If you need stock appearing double pig tail rear springs we have 14” free length springs available in a wide range of spring rates. You can see them here.
Tip: Ford Mustang and GM metric chassis stock pig tail spring size is 5.5” OD with an 11” Free Length.
Additional Landrum Performance Springs technical information can be found here.